| LizardSkin Ceramic Insulation |
| LizardSkin SC- Sound Control |
Custom Product Sales
LizardSkin Application
 | |  | |  | |  |
A premium spray-on insulation for all cars and trucks, street
experimental aircraft, and high end audio installations,
wherever heat and noise are a problem.
How to calculate gallons needed:
Measure length x width of all surfaces to be coated
Add all numbers for total area in square feet
Divide by 25 for Gallons Bucket LizardSkin® Ceramic Insulation
Divide by 50 for Gallons Bucket LizardSkin® SC needed
LizardSkin Coverage Guidelines:
Vehicle Ceramic Insulation
Older style Pickup
1940-1960 2 gal. - 1 unit
3-5 Window Coupe 4 gal. - 2 units
2-door Sedans
1933-1939 6 gal. - 3 units
Chevy/Ford
1955-1957 8 gal. - 4 units
Note: If spraying Ceramic Insulation on both interior and exterior floor, spray .020 on
interior floor, and .020 on exterior floor to achieve .040 total.
Recommended Original Insulation thickness: 40 to 60/1000ths. Recommended for Sound
Control thickness: 20 to 25/1000ths.
Applying LizardSkin® Ceramic Insulation & LizardSkin® SC
For maximum sound control and insulation performance, both LizardSkin
coatings may be used, but it is important that LizardSkin® SC always be
applied FIRST. When used in tandem, LizardSkin® SC should be applied at
least 12 hours prior to application of LizardSkin® Ceramic Insulation.
Important: Manufacturers Recommendations:
For best results, LizardSkin must be applied with a recommended spray gun/nozzle at
50-70 psi air pressure. For specific recommendations, consult product label. Brushing
is recommended only for small area touch up.
Typical Tools Required: LizardSkin® Super Pro spray gun kit
Variable speed 3/8”-1/2” electric drill
Box cutter or knife
Compressed air source: 60-100 psi @ 5 CFM (min)
Access to water for cleanup
Surface Preparation:
Surface to be coated must be clean, dry and free of rust or other corrosion. Mask
areas not intended to be sprayed since coating will adhere to any unmasked area.
Carbon steel surfaces require primer. Aluminum and stainless steel do not need
primers but must be clean and dry.
Product Preparation/Mixing:
LizardSkin® should be mixed thoroughly using a power drill with the mixer paddle bit.
Open the container using the tear tab on the side of the top.
Pull tab and remove lid.
Mix LizardSkin® using variable speed drill and stir paddle bit at low rpm (300 or less)
to a smooth consistency. (Normally 2-4 min.)
Clean stir paddle in water bucket immediately after mixing. Replace lid on bucket until
ready to spray.
After mixing, lift mix paddle from LizardSkin. If product drips off slowly, it is ready to
apply.
LizardSkin® Sound Control Formula
LizardSkin® SC formula is an advanced, water-based composition of high-grade acrylic
binders with sound-damping particles. Proven sound damping technology enables
LizardSkin® SC to dramatically reduce noise when properly applied.
It also protects surfaces from moisture and corrosion and can withstand temperatures
to 300° F. (149° C.)
LizardSkin® SC is used by custom car, street rod, truck builders and RV owners who
want to reduce unwanted noise and/or enhance the sound of their high end audio
systems. It is best applied by special spray gun to a clean and dry primed or painted
rust-free steel. Typical applications include fire walls, floor pans, transmission tunnels,
doors, hoods, trunk lids, under headliners, inside fenders, panel van walls and other
areas that generate vibration and noise. For maximum acoustic performance, coat entire
interior surface and the floor inside and out.
Sound Control: Dramatically reduces noise and vibration
Protect surfaces from moisture and corrosion
Withstand temperatures to 300° F.
Class A Fire-rated
A 2-gallon Bucket covers approximately 100 sq. ft. @ 20/1000's (Max
thickness 40/1000's for maximum effectiveness)
LizardSkin® SuperPro Spray Gun Kit
The SuperPro spray gun kit provides exactly what’s needed for professionals
and hobbyists to properly apply amazing LizardSkin® coatings Typical spray
guns used for paint application are simply not engineered to handle the higher
density of these high technology coatings.
Professional quality spray gun designed to handle the high density and
viscosity of LizardSkin® Ceramic Insulation and LizardSkin® SC
Included one-quart cup can be used for application to small areas
One stir paddle (Attach to drill)
One 48” siphon hose (5/8 Inch ID Thick Wall Rubber)
One 12-inch siphon tube (1/2 Inch ID, 5/8 Inch OD Metal Conduit)
Two hose clamps, one threaded hose barb
LizardSkin coatings should not be applied when ambient temperature is below
70 degrees.
experimental aircraft, and high end audio installations,
wherever heat and noise are a problem.
- Environmentally friendly, water-based
- Class A fire-rated
- No respirator needed; dust mask/protective eye wear recommended
- Spay application only; brush for small areas or touch up.
- Can cover hard to reach places like inner door panels
- Cleans up with soap & water
- Each 2-gallon container covers 46-50 sq. Feet @ .040”
- Reduce engine and solar heat transfer by 25-30 degrees or more
- Reduce noise by 10-12 decibels or more
- Protect surfaces from moisture and corrosion
- Withstand temperatures to 500° F. (260° C.)
How to calculate gallons needed:
Measure length x width of all surfaces to be coated
Add all numbers for total area in square feet
Divide by 25 for Gallons Bucket LizardSkin® Ceramic Insulation
Divide by 50 for Gallons Bucket LizardSkin® SC needed
LizardSkin Coverage Guidelines:
Vehicle Ceramic Insulation
Older style Pickup
1940-1960 2 gal. - 1 unit
3-5 Window Coupe 4 gal. - 2 units
2-door Sedans
1933-1939 6 gal. - 3 units
Chevy/Ford
1955-1957 8 gal. - 4 units
Note: If spraying Ceramic Insulation on both interior and exterior floor, spray .020 on
interior floor, and .020 on exterior floor to achieve .040 total.
Recommended Original Insulation thickness: 40 to 60/1000ths. Recommended for Sound
Control thickness: 20 to 25/1000ths.
Applying LizardSkin® Ceramic Insulation & LizardSkin® SC
For maximum sound control and insulation performance, both LizardSkin
coatings may be used, but it is important that LizardSkin® SC always be
applied FIRST. When used in tandem, LizardSkin® SC should be applied at
least 12 hours prior to application of LizardSkin® Ceramic Insulation.
Important: Manufacturers Recommendations:
For best results, LizardSkin must be applied with a recommended spray gun/nozzle at
50-70 psi air pressure. For specific recommendations, consult product label. Brushing
is recommended only for small area touch up.
Typical Tools Required: LizardSkin® Super Pro spray gun kit
Variable speed 3/8”-1/2” electric drill
Box cutter or knife
Compressed air source: 60-100 psi @ 5 CFM (min)
Access to water for cleanup
Surface Preparation:
Surface to be coated must be clean, dry and free of rust or other corrosion. Mask
areas not intended to be sprayed since coating will adhere to any unmasked area.
Carbon steel surfaces require primer. Aluminum and stainless steel do not need
primers but must be clean and dry.
Product Preparation/Mixing:
LizardSkin® should be mixed thoroughly using a power drill with the mixer paddle bit.
Open the container using the tear tab on the side of the top.
Pull tab and remove lid.
Mix LizardSkin® using variable speed drill and stir paddle bit at low rpm (300 or less)
to a smooth consistency. (Normally 2-4 min.)
Clean stir paddle in water bucket immediately after mixing. Replace lid on bucket until
ready to spray.
After mixing, lift mix paddle from LizardSkin. If product drips off slowly, it is ready to
apply.
LizardSkin® Sound Control Formula
LizardSkin® SC formula is an advanced, water-based composition of high-grade acrylic
binders with sound-damping particles. Proven sound damping technology enables
LizardSkin® SC to dramatically reduce noise when properly applied.
It also protects surfaces from moisture and corrosion and can withstand temperatures
to 300° F. (149° C.)
LizardSkin® SC is used by custom car, street rod, truck builders and RV owners who
want to reduce unwanted noise and/or enhance the sound of their high end audio
systems. It is best applied by special spray gun to a clean and dry primed or painted
rust-free steel. Typical applications include fire walls, floor pans, transmission tunnels,
doors, hoods, trunk lids, under headliners, inside fenders, panel van walls and other
areas that generate vibration and noise. For maximum acoustic performance, coat entire
interior surface and the floor inside and out.
Sound Control: Dramatically reduces noise and vibration
Protect surfaces from moisture and corrosion
Withstand temperatures to 300° F.
Class A Fire-rated
A 2-gallon Bucket covers approximately 100 sq. ft. @ 20/1000's (Max
thickness 40/1000's for maximum effectiveness)
LizardSkin® SuperPro Spray Gun Kit
The SuperPro spray gun kit provides exactly what’s needed for professionals
and hobbyists to properly apply amazing LizardSkin® coatings Typical spray
guns used for paint application are simply not engineered to handle the higher
density of these high technology coatings.
Professional quality spray gun designed to handle the high density and
viscosity of LizardSkin® Ceramic Insulation and LizardSkin® SC
Included one-quart cup can be used for application to small areas
One stir paddle (Attach to drill)
One 48” siphon hose (5/8 Inch ID Thick Wall Rubber)
One 12-inch siphon tube (1/2 Inch ID, 5/8 Inch OD Metal Conduit)
Two hose clamps, one threaded hose barb
LizardSkin coatings should not be applied when ambient temperature is below
70 degrees.
LizardSkin® Ceramic Insulation formula is an advanced,
water-based composition of high-grade acrylic binders with
air-filled insulating/reflective and sound-absorbing particles.
water-based composition of high-grade acrylic binders with
air-filled insulating/reflective and sound-absorbing particles.
